WEBELOS ACTIVITY BADGE TIE SLIDES

PHYSICAL SKILLS	MENTAL SKILLS	COMMUNITY	TECHNOLOGY	OUTDOOR
AQUANAUT ATHLETE FITNESS SPORTSMAN	ARTIST SCHOLAR SHOWMAN TRAVELER	CITIZEN COMMUNICATOR FAMILY MEMBER READYMAN	CRAFTSMAN ENGINEER HANDYMAN SCIENTIST	FORESTER GEOLOGIST NATURALIST OUTDOORSMAN

Compiled by
TERRI HICKS, Henderson, NV

ARTIST

PAINTER'S PALETTE TIE SLIDE MATERIALS: SMALL PIECE OF LIGHT BROWN FUN FOAM, SMALL AMOUNTS OF 5 DIFFERENT COLORS OF PAINT, 1 SMALL PAINT BRUSH, 1/4" PVC RING. SUPPLIES: SCISSORS, PENCIL, HOT GLUE GUN INSTRUCTIONS: TRACE PALETTE PATTERN ON FUN FOAM AND CUT OUT. PLACE A DOLLOP OF EACH COLOR OF PAINT AROUND THE EDGE OF PALETTE SHORT PAlNT BRUSH BY ABOUT 1 1/2". SAND HANDLE TO LOOK LIKE THE ORIGINAL AND PAINT TO MATCH. INSERT PAINT BRUSH THROUGH THUMB HOLE IN PALETTE AND GLUE IN PLACE. GLUE PVC RING TO THE BACK.

COMMUNICATOR

COMPUTER CHIP TIE SLIDE MATERIALS: 1 1/2" x 1 1/2" SQUARE OF WHITE FUN FOAM & LIGHT WEIGHT CARDBOARD, COLORED TELEPHONE WIRE, THIN FLORAL WIRE, SMALL COLORED BEADS WITH HOLE IN CENTER, 1/4" PVC RlNG. SUPPLIES: SCISSORS, TOOTHPICK, HOT GLUE GUN. INSTRUCTIONS: CUT FLORAL WIRE INTO 1 1/2" PIECES. THREAD BEADS ONTO FLORAL WIRE LEAVING A LITTLE PIECE AT EACH END TO TURN DOWN AND POKE INTO THE FUN FOAM. TWIST TELEPHONE WIRE AROUND A TOOTHPICK TO FORM SMALL COILS INSERT COILS AND BEADED WIRE INTO THE FUN FOAM IN ANY ARRANGEMENT YOU WISH TO MAKE A COMPUTER CHIP AFTER FUN FOAM IS COVERED WITH BEADS AND COILS. HOT GLUE THE FUN FOAM ONTO THE CARDBOARD FOR ADDED SUPPORT. HOT GLUE PVC RING TO BACK OF CARDBOARD.

READYMAN

FIRST AIDE TIE SLIDE MATERIALS: 1 WHITE FILM CANISTER, 1 - 3 1/2" x 1 3/4" PIECE OF WHITE PAPER, 1 - 1/4" PVC RING, AND VARIOUS 1st AIDE SUPPLlES. SUPPLIES: RED MARKER, SCISSORS AND HOT GLUE GUN INSTRUCTIONS: TRACE RED CROSS PATTERN ONTO CENTER OF PAPER. AND COLOR IN WITH RED MARKER INSERT PAPER INTO FILM CANISTER SO CROSS SHOWS THROUGH. PLACE 1ST AIDE ITEMS IN CANISTER. (i.e. BANDAIDE, STERILE WIPE, NEEDLE, THREAD, BUTTON, SAFETY PIN, ASPIRIN, 35 CENTS FOR PHONE CALL, ETC) HOT GLUE PVC RING ON BACK OF CANISTER.

SPORTSMAN

WATER SKI TIE SLIDE MATERIALS: 2 CRAFT STICKS, 1 MATCH STICK, 8" OF EMBROIDERY FLOSS, 1 - 1/4" PVC RING SUPPLIES: MARKERS, SANDPAPER, HOT GLUE GUN, SCISSORS, AND SOMETHING TO CUT CRAFT STICKS WITH. INSTRUCTIONS: CUT CRAFT STICKS TO 3" LENGTH. COLOR CRAFTS STICKS WITH MARKERS IN YOUR OWN DESIGN. GLUE STICKS TOGETHER IN AN "X" SEPARATE EMBROIDERY FLOSS INTO TWO THREE STRAND PIECES. TIE ONE THREE STRAND PIECE INTO A BOW & GLUE ONTO CENTER OF SKIS. CUT MATCHSTICK INTO A 5/8" PIECE AND GLUE ACROSS THE TWO ENDS OF FLOSS TO FORM THE TOW LINE HANDLE. HOT GLUE PVC RING TO BACK OF SKIS.

Feedback to Terri!
Copyright 1997, 1998 © by Terri Hicks. All rights reserved.